Dishlex 500e manual

I am curious about an electrical switch behind the kick panel with multiple terminals 4 or 5 and the switch has small hose leading to the drain pan.

I think it might be some kind of flood control safety switch. It is not critical at this time that I know what this switch does, but the manual might tell me, and the manual will be necessary next time this machine fails my wife. I like to keep her very happy. Electrolux has taken over new models of Dishlex. I noticed that some parts are evailable on Ebay and are packed in Electrolux bags. I have the original user manual, and I don't need the wiring diagram. I already fixed the broken door wiring.

We have placed cookies on your device to help make this website better. You can adjust your cookie settings , otherwise we'll assume you're okay to continue. Appliance Repair Training Webinar Recordings. Regency VSA E dishwasher manual. Share More sharing options Followers 3. Recommended Posts. The information over here helps a lot. What happens if you squirt some starting fluid down the throttle body - will it fire briefly, or still nothing?

Yes, the engine should start with a defective throttle body, unless it has a serious defect. Did check the testlight on my w and then it works. So there is also no spark at al. Is possible to check cranck shaft sensor? Found the cable. And the connector on the computer. Rufrob EE Newbie. I am having a similar problem. My car was off the road for 5 years. I put gas in, it would start and stall after a few second. It would not take any throttle. I cleaned the distributor car and rotor.

No change. I notice the fuel didnt smell right so I drained the fuel and noticed the tank was rusty inside. So I removed the tank, cleaned it and reinstalled it with new strainer and fuel filter. Now it wont start at all. I hear the fuel pump priming but I could not see any pressure in the fuel rain and no spark. I put power to both FPs directly and they work. So I will try charging the battery again. The harnesses look good with not deteriorated insulation, upper nor lower.

I will check the injectors next too. If the fuel pumps run but there is no pressure at the rail, you have fuel delivery problems that need to be sorted out first. Also try squirting starting fluid into the intake and see if it fires briefly, if so, you have spark.

Thanks GSXR, you were right. I heard the FP but it turns out only the lead pump was working. I put fuel in the intake and it ran. So I just ordered a new FP. Mine still dont start. Renew the crackshaft sensor, but that does not help. One thing is sure kow, the EZL doesn't do anything. It should put one site of the coil to the ground. But nothing. Both coils nothing. I also cheked the enige speed contact to LH injectie computer but also nothing.

For a test I removed al computers exept the base module. But nothing changed. I removed the EZL and it looks it is changed before, it has a stamp on it M09 93 thats is production year? What i noticed, the white coollant stuf was not applied correctly. I be grateful for all help. Do you have access to another EZL to swap in for testing? It can be from any M with LH injection. And not done propely. I gone look for another one, But V8 engines pretty rare here in the netherlands.

But saw a few in germany. But gone take a few days. Doest a unit from E also fit? Thanks, clear, explains the price differences, the 5. But will get one! Will look for another EZL. I openend this one. See picture. The EZL does not work. So I got a used EZL So that is nice. Let run the engine for few minutes. And than got a other issue. When warm, it starts to misfire at iddle. If I rev the enige it seems oke. Turn off the engine. And start it again, but it doesn't. I think got a few things: -The used EZL is not okay.

Pretty hard to get the car running! Try tomorrow again with cold engine. Thanks for advise so far. And, inspect for liquid behind the insulators. And, if you waited hours, it may have restarted, if the issue is secondary ignition system.

Yesterday I clean up the distibution caps, Rotorts and isolators. I have to order new ones. They ar used. Started the engine, and yess real good. Let it idle for few minutes. Drive a little bit. And all okay. Let it idle for few time. Engine was all heated up. Turn it off, wait 15 minutes en start it again.

Remove the caps, and the left one was full of moisture. Clean both caps. Now it starts runs for one seconds en dies. Wil try it today with cold engine. So I orded new caps, rotos and isolators and seals. Read a lot of post of this kind problems. So I gone renew all parts. The only connections I dont see, there must be a problem with the carter breather hose? Thanks a lot!

Eno EE Guru. Check the electrical ground and make sure there is proper power supply into the fuel pumps. Stil have some trouble. Starts, runs for a second and die. Did use a fuelpressure meter today. Looks like the pressure is far to high. If i drain the retour line so it is empty the cars runs for a minute. I made short film, will try to upload it. What was the pressure?

Giving gas is lowers too 48PSI I blow the return hose, but looks free. Started again and then runs great for a minut, stationary 45 PSI. How do I go about getting a manual for this dishwasher it is 2 years old. When washing glasses it has a film never looks clean. I have changed dishwasher soap and I am also using the other airdry. Not happy with dishwasher Manuals are usually available on line.

The film could be from hard water. Check with local municapal authorities and see. If the local water hardness level above 9 then a water softener is required. The soap dispenser does not open. In the past I've used dishwasher magic or similar to clean the dishwasher of hardwater deposits and that solved the problem. The cover opens and closes manually. The springs seem fine. I removed the door skin and the linkages look good.

I checked the resistance on the Wax motor and it is with in spec, approximately ohms. I 've watched the cycle and the wax motor never seems to actuate. I put my meter on th The Upper Spray Arm came off and I need the manual to figure out how to get it back on or get a new piece. I am having the same problem, did you find an answer?

I am unable to locate the manual on your site and would like to have the manual on hand. Can you help with that? I have a Dishlex Dishwasher with a manual timer. The timer i believe is broken, when i place it on a wash any wash it clicks however does not engage??

Can you help me Replace Control panel cover on dishlex dishwasher E If your E is the same as my E then the controls are electronic touch buttons.

The are part of a self adhesive strip and stuck to the front of the door.